Shed Matters 3

User avatar
chinatyke
Donor
Posts: 2481
Joined: 21 Apr 2012, 13:14
Location: Pingguo, Guangxi, China

Re: Shed Matters 3

Post by chinatyke » 13 Aug 2019, 12:19

You're getting to be like Norman Clegg in Last of the Summer Wine where he was constantly painting his front gate - it's time you got your teeth into another model!

User avatar
Big Kev
Global Moderator
Global Moderator
Posts: 3173
Joined: 23 Jan 2012, 20:15
Location: Barlick

Re: Shed Matters 3

Post by Big Kev » 13 Aug 2019, 16:01

Has anyone got a damp meter I can borrow for half an hour?

The survey on my house picked up a high moisture level in the chimney breast in the loft, looks like the flashing has failed. An easy enough fix. I've cut out the bit of plasterboard on the ceiling and a bit of plaster on the wall, everything looks dry but I want to check the levels in the timber before I put it all back together.
Kev

A Resigned Observer

User avatar
plaques
Donor
Posts: 3660
Joined: 23 May 2013, 22:09

Re: Shed Matters 3

Post by plaques » 13 Aug 2019, 17:52

Big Kev wrote:
13 Aug 2019, 16:01
Has anyone got a damp meter I can borrow for half an hour?
Sorry no damp meter but at a push you could use one of those digital voltmeters and measure the resistance across two pins. You would have to do your own calibration by comparing different dry / damp materials. perhaps Ian would advise on this.

Damp in loft chimney breast. Our house was dripping with water but not from faulty flashing but down the chimney. The fault was someone had fitted a stop ventilator plug which wasn't the normal mushroom shape and without sealing the fitment tube the water just drained down the chimney. Worth having it checked out.

User avatar
Big Kev
Global Moderator
Global Moderator
Posts: 3173
Joined: 23 Jan 2012, 20:15
Location: Barlick

Re: Shed Matters 3

Post by Big Kev » 13 Aug 2019, 19:21

I was in luck, my neighbour had one. 10% in the structural timber (9-14%) is acceptable and 0.2% in the plaster. Looks like it was a recent failure and the moisture was just in the ceiling boards.
Kev

A Resigned Observer

User avatar
Stanley
Global Moderator
Global Moderator
Posts: 52553
Joined: 23 Jan 2012, 12:01
Location: Barnoldswick. Nearer to Heaven than Gloria.

Re: Shed Matters 3

Post by Stanley » 14 Aug 2019, 02:49

China, you aren't dealing with the side effects of immunotherapy. I shall move on another model when the time feels right.
Stanley Challenger Graham
Stanley's View
scg1936 at talktalk.net

"Beware of certitude" (Jimmy Reid)
The floggings will continue until morale improves!

User avatar
Stanley
Global Moderator
Global Moderator
Posts: 52553
Joined: 23 Jan 2012, 12:01
Location: Barnoldswick. Nearer to Heaven than Gloria.

Re: Shed Matters 3

Post by Stanley » 18 Aug 2019, 05:32

Am considering painting the gate..... Or something equally important!
Stanley Challenger Graham
Stanley's View
scg1936 at talktalk.net

"Beware of certitude" (Jimmy Reid)
The floggings will continue until morale improves!

User avatar
Bodger
Senior Member
Posts: 1148
Joined: 23 Jan 2012, 12:30
Location: Ireland

Re: Shed Matters 3

Post by Bodger » 18 Aug 2019, 07:26


User avatar
Bodger
Senior Member
Posts: 1148
Joined: 23 Jan 2012, 12:30
Location: Ireland

Re: Shed Matters 3

Post by Bodger » 18 Aug 2019, 07:32

A bit more, read the report on the left of the page
https://trove.nla.gov.au/newspaper/article/6047696

User avatar
Stanley
Global Moderator
Global Moderator
Posts: 52553
Joined: 23 Jan 2012, 12:01
Location: Barnoldswick. Nearer to Heaven than Gloria.

Re: Shed Matters 3

Post by Stanley » 18 Aug 2019, 07:59

All too common Bodge in those days. One thing that caught my attention is that the picture of the engine is not the right one, that engine was built a lot later than the 1863 mentioned in the inquest report.
Stanley Challenger Graham
Stanley's View
scg1936 at talktalk.net

"Beware of certitude" (Jimmy Reid)
The floggings will continue until morale improves!

User avatar
Stanley
Global Moderator
Global Moderator
Posts: 52553
Joined: 23 Jan 2012, 12:01
Location: Barnoldswick. Nearer to Heaven than Gloria.

Re: Shed Matters 3

Post by Stanley » 25 Aug 2019, 07:20

Image

A bit of a useful potter this morning. I cleaned the VM up and went round all the oil and grease nipples. When you're doing stuff lubrication gets forgotten so It's a good idea to go round and give them all a shot or two occasionally.
Stanley Challenger Graham
Stanley's View
scg1936 at talktalk.net

"Beware of certitude" (Jimmy Reid)
The floggings will continue until morale improves!

User avatar
Stanley
Global Moderator
Global Moderator
Posts: 52553
Joined: 23 Jan 2012, 12:01
Location: Barnoldswick. Nearer to Heaven than Gloria.

Re: Shed Matters 3

Post by Stanley » 31 Aug 2019, 07:18

I pottered for an hour. That's enough at the moment, I have laid off too long and need to get back in training!

Image

I had a 9/16" cutter that badly needed attention so I fired up the T&C grinder and sharpened it, I did the current 3/4" cutter that's in the mill as well. It wasn't bad but will benefit from a gulleting and a touch up.

Image

In the same vein, I got the Picador drill sharpening jig down off the shelf and sharpened two 1/2" drills that have shown signs of needing a reset. I'm pretty good at hand sharpening but over time you can drift off correct angles.
That was enough for this morning. It did the T&C grinder good to be fired up. The motor and spindle bearings are very high speed and its a good thing to keep the lubricant fluid, the best way to do that is run them.
A useful hour.....
Stanley Challenger Graham
Stanley's View
scg1936 at talktalk.net

"Beware of certitude" (Jimmy Reid)
The floggings will continue until morale improves!

Post Reply

Return to “Crafts”